Reverse Engineering of a Pelton Wheel - Part Three: Automatic surface creation

images/download/attachments/137619467/INtro.PNG

Introduction

Reverse engineering is the creation of CAD surfaces from scan data.

In most cases, a scanner provides the point clouds used to create a 3D mesh. Then, CAD surfaces can be computed from the 3D mesh and a polyline network. CAD surfaces can be exported in IGES or STEP format and further used in other software for Computer Aided Manufacturing (CAM), Finite Element Analysis (FEA) or for comparison and inspection.

This exercise is part of full workflow that shows how to convert a point cloud into a CAD model. The steps below give a global description of the full process:

  1. Align the part thanks to the extraction of geometric features on a mesh created from the point cloud

  2. Clean the mesh so that it can be replicated by symmetry and rotation

  3. Create an automatic network of polylines and edit this network in the required areas to create the surface - this is the part covered in this exercise

Exercise overview

As shown in the figure below, the input mesh of this exercise has been created in a very precise manner so that the borders are exactly planar, circular and front and back fit exactly.

Thanks to this mesh, this exercise will show how to:

  • Automatically create a network of polylines

  • Adjust this network in order to fix it or improve it

  • Create NURBS surfaces from this network

  • Duplicate the NURBS surfaces to create a solid model

The file used in this tutorial in PeltonWheel_Reverse_3-AutoSurface.3dr

The file can be downloaded on Cyclone 3DR - Downloads page.

images/download/attachments/137619467/FrontView.PNG Front view of the input mesh

images/download/attachments/137619467/LeftView.PNG Left view of the input mesh

Automatic creation of the network

Fur such an organic shape, the easiest way to create a network that will later drive the creation of surface patches is to use the tool named Create Network.

Select the mesh and launch this command. There are three options in this command:

  • The length of the target edge for the network

  • A border management option

  • A constraint option (advanced usage, not useful to activate this option in this application)

Border management:

  • For this mesh, considering that the borders were very precisely created, the right option is Extend to border. This way, the network will be extend precisely to the border.

  • You can test with the other options to see the differences

Edge length option:

  • The default value is calculated so that the number of surface patches that would be created remains reasonable.

  • Enter 10 and see that thousands of tiny patches would be created. This is not what we need here.

  • Enter 75 and see that the network is nicely created. Only the area of the thin parts need some adjustments.

  • Hit OK to validate and exit the command


images/download/attachments/137619467/AutoNetwork.PNG Automatic network created

Adjustment of the network

With this network, you can see that the area of the thin parts needs some adjustments.

Actually, the images below show that the network doesn't go until the border.

images/download/attachments/137619467/Area1-ZoomAll.PNG Issue in the created network that needs to be fixed - top view

images/download/attachments/137619467/Area1-ZoomClose.PNG Issue in the created network that needs to be fixed - zoom

Adjustment on the thin part and close to the border

The first area that needs to be fixed is the one that is close to the border

To do so, select the mesh and the network and launch the command Edit Network:

  1. Select the tool allowing to create new segments (the "+" button)

  2. Pick the green ball

  3. Then press Alt and click a point on the border

In creation mode, the Alt key allows to pick an exact point on the network.

With no key pressed, the point will either be at the extremity of a segment, or at the middle of the segment.

The Alt key therefore allows for more precise control.

The segment shown in blue in the image below is also not following very precisely the thin area. We will delete it and recreate so that it follows the edge of the part:

  1. Select the tool allowing to modify the network (the pencil button)

  2. Select the segment

  3. Press delete

  4. Select the tool allowing to create new segments (the + button)

  5. Pick the green ball on the right and then draw the segment so that it reaches the green ball on the right as shown below

  6. Press Enter to validate the segment


images/download/attachments/137619467/NewSegment1.PNG Straight segment replaced with a curved segment - Step 1

images/download/attachments/137619467/NewSegment2.PNG Straight segment replaced with a curved segment - Step 2

images/download/attachments/137619467/NewSegment3.PNG Straight segment replaced with a curved segment - Step 3

Adjustment of the thin part in the middle of the blade

The very same tool will be used to adjust the area which is in the middle of the blade.

Select the mesh and the network and launch the command Edit Network.

The first step here here will be to delete the nodes that will not be used: 2 nodes in the back and 1 node in front as shown in the image below.

Make sure you are in Edit mode. Select these nodes and press Delete on your keyboard.

Use the Ctrl key to select several nodes

images/download/attachments/137619467/NodeDeleteBack.PNG Nodes that need to be selected and deleted - back view

images/download/attachments/137619467/NodeDeleteFront.PNG Nodes that need to be selected and deleted - front view


The next step consists in drawing the segment along the thin part. Process just like before:

  1. Select the tool allowing to create new segments (the + button)

  2. Pick the green ball on the top and then draw the segment so that it reaches the green ball on the bottom as shown below

images/download/attachments/137619467/NewSegment4.PNG Drawing a segment along the thin part


Then repeat the operation on the front of the blade in order to create a line parallel to the thin border as shown below.

images/download/attachments/137619467/NewSegment6.PNG Drawing a segment in the front of the blade

The next step consists in adding segments in order to connect the nodes below and the edge line in the front. Remember to use the Alt key in order to pick a point on the edge line precisely.


images/download/attachments/137619467/NewSegment7.PNG Adding segments to connect the nodes

And repeat the operation on the back:

  1. Draw a segment parallel to the edge line

  2. Connect the nodes below to the ones above (no need to use the Alt key here as the nodes are already created!)

images/download/attachments/137619467/NewSegment8.PNG Same operation repeated on the back of the blade - parallel line

images/download/attachments/137619467/NewSegment9.PNG Same operation repeated on the back of the blade - node connection

Creation of sharp corners in the network

The network is almost ready for creating the NURBS Surfaces.

You can select the network and the mesh and launch the command Generate Patches to look at the result obtained this way.


The images below show the results obtained with this network. From far away, the surface is fine: no holes and smooth. When zooming in, you can see that the corners are not sharp.

Keeping these non sharp corners would not allow to create a connected surface for the full blade.

images/download/attachments/137619467/SurfaceNoCorner-ZoomAll.PNG Default corners are not sharp - front view

images/download/attachments/137619467/SurfaceNoCorner-ZoomIn.PNG Default corners are not sharp - zoom

In order to create sharp corners:

  1. Select the network of polylines and launch the command Ungroup Polyline

  2. Launch the command Cut Polyline and select the option Vertex / End

  3. Zoom in all 4 corners and pick the exact vertex that need to be cut (do not hesitate to zoom in!)

images/download/attachments/137619467/SharpCorners.PNG Polyline cut in the corners

Creation of NURBS surfaces

The NURBS surface is now ready for being created: just select all the polylines and the mesh and launch the command Generate Patches.

The surfaces are created automatically!

images/download/attachments/137619467/Final_Surface.PNG CAD shell created thanks to the network

Creation of the full blade

Creating a symmetry

Now that half of the blade is created, it is very easy to create the full blade:

  1. Select the CAD Surface and launch the Symmetry command

  2. Select the option Planar Symmetry

  3. Define the origin (0, 0, 0) as the Axis position

  4. Define X (1, 0, 0) as the Axis direction

  5. Make sure the option to Create copy is activated

At this point, the 2 surfaces are just independent CAD surfaces. There is no link between them.

The link can be created thanks to the command Sew Surfaces:

  • Select the two CAD surfaces and launch this command

  • Enter 0 in the Tolerance value (the exact same borders are used on both side of the blade allowing to enter 0 here)

  • Press preview and see the number of output free contour is 1

  • Hit OK, Exit to validate the command

images/download/attachments/137619467/image2020-5-12_14-4-51.png Duplicating the blade by symmetry and sewing

Creating all 18 blades

The next step consists in duplicating the blade so that the full wheel is created.

To do so, copies of the blade have to be created by rotation:

  1. Select the shape

  2. Launch the command Rotation

  3. Define the Axis position as the origin (0, 0, 0)

  4. Define the Axis direction as X (1, 0, 0)

  5. Set the angle to 20°

  6. Check the box to create 17 copies

  7. Validate with OK

In total, this will create 18 blades (the initial one plus the 17 copies)

These 18 CAD shapes are now individual shapes with no connection. The next step consists in sewing them:

  1. Select these 18 blades

  2. Launch Sew Surfaces

  3. Enter a tolerance value of 0.5mm

  4. Hit Preview and validate with OK, Exit

The wires in front and back of the blade are not exactly mathematically the same because the network that was used did not consider any constraints in the front and back of the blade.

For this reason, a value of 0.5mm is necessary here.

Note that the number of output free contours is 2 here: on each side of the wheel

images/download/attachments/137619467/18_blades.PNG Duplicating the blade by rotation and sewing

Creating a solid model

The CAD model created at previous step is almost a solid: only 2 holes remain to be filled. This final step consists in filling them:

  1. Select the CAD shape and launch the command From CAD Surface

  2. The 2 external wires are extracted

  3. Select the first wire, launch the command Fill Surface and press OK

  4. Repeat the operation with the second wire

These operations created 2 surfaces restricted by the input wires.

In order to create a solid:

  1. Select the 2 planar surfaces and the CAD surface of the 18 blades

  2. Launch the command Sew Surfaces

  3. Enter 0 in the tolerance

  4. Hit OK to validate the result

The shape is now a solid model of a pelton wheel.

images/download/attachments/137619467/SolidBladeModel.PNG Final solid model of a Pelton wheel

This CAD solid model can now be exported to STEP file for further processing:

  • Being machined by a CAM software

  • Or being analyzed in a CAE software package